OpenBCM V1.07b12 (Linux)

Packet Radio Mailbox

SR8BBS

[OBCM_Lublin]

 Login: GUEST





  
G8MNY  > TECH     25.04.24 03:04z 53 Lines 2363 Bytes #29 (0) @ WW
BID : 6168_GB7CIP
Subj: AKD's VHF/UHF Wavemeter WA1
Path: SR8BBS<SR4BBX<SR1BSZ<IW0QNL<JH4XSY<N3HYM<W9GM<N6PNK<VK2RZ<GB7CIP
Sent: 240424/0842Z @:GB7CIP.#32.GBR.EURO #:6168 [Caterham Surrey GBR] $:6168_GB
From: G8MNY@GB7CIP.#32.GBR.EURO
To  : TECH@WW

By G8MNY                                                (New May 05)
(8 Bit ASCII graphics use code page 437 or 850, Terminal Font)

This device is used to peaking up or "seeing RF" around your Tx aerial.

Here is a reverse engineered diagram of one I picked up the other day.

       ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÄ¿
       ³                          ÚÄÄÄÄÄÄÄ)ÄÄÄÄÄÄÄ)ÄÄÂ1K2ÄÂÄÄ¿   |)      390K
       ³ VHF           \³/        ³       ³     METER³    ³ _³_  |) L3     ³
      o´  o       8p2   ³        10k     1M       ³  ³    ³ /_\   ³        ³
 ÚoÄÄ> ³OFF<ÄÄoÂÄÄÄ´ÃÄÄÄo     ÚÄ>FREQ     ³  BF547³  ³ 10n³  ³D3  ÃÄÄÄ´ÃÄÄÄ´
_³_   o´  o    ) L1       39p ³  POT      ³   T1³/  _³_  === ³   |)   10n  ³
 Ü 9V  ³  ³UHF ÃÄÄÂÄÄÄÄÄÄÄ´ÃÄÄ)ÄÄÄ)ÄÄÄÄÂÄÄ)Ä´>ÃÄ´   /_\'  ³  ³   |) L4     ³
_³_    ³  ³    ³  ³ 1n        ³   ³    ³  ³ D2  ³\e  ³24V ³  ÃÄÄÄÄ´        ³
 Ü    === ³    )  ÃÄÄ´ÃÄÂÄ12KÄ´ PRESET ³  ³       ³  ³Z1  ³  ³     \³BF547 ³
 ³  10n³  ³ L2 )  ³/\  _³_    ³  22k   ³  SET     ³  ³    ³  ³   T2 ÃÄÄÂÄÄÄ´
 ³     ³  ³    ) ===   ÄÄÄD1 ===  ³    ÀÄ´ZERO    ³  ³    ³ ===   e/³ 39K _³_
 ³     ³  ³    ³/ ³Ct  /_\ 10n³   ³       4M      ³  ³    ³  ³n22 ³    ³  /_\
 ÀÄÄÄÄÄÁÄÄÁÄÄÄÄÁÄÄÁÄÄÄÄÄÁÄÄÄÄÄÁÄÄÄÁÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÁÄÄÁÄÄÄÄÁÄÄÁÄÄÄÄÁÄÄÄÄÁÄÄÄÙD4
           TUNED CIRCUITS            DETECTOR   AMP            DC INVERTER

L1 = 2T 23mm dia, L2 = 4T 7mm dia, L3 & L4 1mH ?

HOW IT WORKS
When switched to VHF/UHF the DC interter T2 D4 & D3 is powered. It
oscillates to provide >24V, which is fed to the 24V zener Z1 to make the
maximum varicap D1 tuning voltage.

In VHF mode at max tuning voltage L2 & Ct set the highest frequency of 200MHz.
The lowest frequency of 120MHz is determined by the voltage set by the preset.

On UHF mode L1 is placed across L2 to raise the frequency between 195 to
450MHz, & the slight inductance of the ground track gives the low Z aerial
coupling needed @ UHF.

The RF detector diode D2 feeds the base of T1 to current amplify the signal for
the meter. The 4M pot sets the bias level to set meter zero so that D2 & T1
are at the point of conduction.


Also look at my TECH buls on "Piston Absorption Wavemeter", "BURNS's MF-UHF
Wavemeter TC-101", & "RF Field Indicatopr FL-30AH".


Why Don't U send an interesting bul?

73 de John G8MNY @ GB7CIP



Read previous mail | Read next mail


 26.04.2024 19:56:26zGo back Go up